                   .:                     :,                                          
,:::::::: ::`      :::                   :::                                          
,:::::::: ::`      :::                   :::                                          
.,,:::,,, ::`.:,   ... .. .:,     .:. ..`... ..`   ..   .:,    .. ::  .::,     .:,`   
   ,::    :::::::  ::, :::::::  `:::::::.,:: :::  ::: .::::::  ::::: ::::::  .::::::  
   ,::    :::::::: ::, :::::::: ::::::::.,:: :::  ::: :::,:::, ::::: ::::::, :::::::: 
   ,::    :::  ::: ::, :::  :::`::.  :::.,::  ::,`::`:::   ::: :::  `::,`   :::   ::: 
   ,::    ::.  ::: ::, ::`  :::.::    ::.,::  :::::: ::::::::: ::`   :::::: ::::::::: 
   ,::    ::.  ::: ::, ::`  :::.::    ::.,::  .::::: ::::::::: ::`    ::::::::::::::: 
   ,::    ::.  ::: ::, ::`  ::: ::: `:::.,::   ::::  :::`  ,,, ::`  .::  :::.::.  ,,, 
   ,::    ::.  ::: ::, ::`  ::: ::::::::.,::   ::::   :::::::` ::`   ::::::: :::::::. 
   ,::    ::.  ::: ::, ::`  :::  :::::::`,::    ::.    :::::`  ::`   ::::::   :::::.  
                                ::,  ,::                               ``             
                                ::::::::                                              
                                 ::::::                                               
                                  `,,`


http://www.thingiverse.com/thing:1288929
Micro Staunton Chess Set by CMB27 is licensed under the Creative Commons - Attribution license.
http://creativecommons.org/licenses/by/3.0/

# Summary

I call this a Micro Chess Set because each square of the board is 1" x 1" making the total board size 8" x 8". In order to artificially add weight to the pieces, each chess piece has a small magnet in its base, and each board square has a threaded hole for a set screw. The pieces are based on Staunton chess sets. The board was inspired by other chess boards on Thingiverse. In order to save time and resources a paper board has also been included; if you choose to use the paper board it is unnecessary to 3D print any of the board components or purchase the magnets and setscrews.

A complete set will require the following:

Light Colored Pieces
2 x Piece Bishop
1 x Piece King
2 x Piece Knight
8 x Piece Pawn
1 x Piece Queen
2 x Piece Rook

Dark Colored Pieces
2 x Piece Bishop
1 x Piece King
2 x Piece Knight
8 x Piece Pawn
1 x Piece Queen
2 x Piece Rook

Light Colored Board Squares
18 x Board Middle
3 x Board EdgeA
3 x Board EdgeB
3 x Board EdgeC
3 x Board EdgeD
1 x Board CornerA
1 x Board CornerC

Dark Colored Board Squares
18 x Board Middle
3 x Board EdgeA
3 x Board EdgeB
3 x Board EdgeC
3 x Board EdgeD
1 x Board CornerB
1 x Board CornerD

Other Components
32 x Magnet (1/4" diameter x 1/16" height) 
http://www.digikey.com/product-search/en?keywords=469-1005-ND
64 x Set Screw (1/4"-20 thread x 3/16" length)
http://www.mcmaster.com/#92311a532/=10t4414

Printing Recommendations:
The pieces, not board, should be printed with 100% fill.
The knight will require a support, this can likely be added by your slicing software.
If printing the paper chess board, it is best to print it without scaling it up or down.